From 1761772a023fc1208ac282b0eaf10c2f646d2b03 Mon Sep 17 00:00:00 2001
From: "W. Trevor King" <wking@tremily.us>
Date: Wed, 26 Jun 2013 08:29:14 -0400
Subject: [PATCH] Don't specify .png in \includegraphics{}

LaTeX figures out valid extensions automatically.
---
 src/calibcant/discussion.tex | 2 +-
 src/calibcant/procedure.tex  | 6 +++---
 src/introduction/main.tex    | 2 +-
 src/pyafm/frameworks.tex     | 2 +-
 4 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/src/calibcant/discussion.tex b/src/calibcant/discussion.tex
index b40f38a..36330d5 100644
--- a/src/calibcant/discussion.tex
+++ b/src/calibcant/discussion.tex
@@ -113,7 +113,7 @@ the calculated $\kappa$.
 
 \begin{figure}
   \begin{center}
-    \includegraphics[width=0.8\textwidth]{figures/calibcant/statistics.png}
+    \includegraphics[width=0.8\textwidth]{figures/calibcant/statistics}
     \caption{Estimating the statistical uncertainty of the calculated
       cantilever spring constant $\kappa$ through repeated
       measurements.\label{fig:calibcant:statistics}}
diff --git a/src/calibcant/procedure.tex b/src/calibcant/procedure.tex
index 04b4d73..a1da8c1 100644
--- a/src/calibcant/procedure.tex
+++ b/src/calibcant/procedure.tex
@@ -34,7 +34,7 @@ during this approach--retract cycle is analyzed to measure $\sigma_p$
 
 \begin{figure}
   \begin{center}
-    \includegraphics[width=0.8\textwidth]{figures/calibcant/bump.png}
+    \includegraphics[width=0.8\textwidth]{figures/calibcant/bump}
     \caption{Measuring the photodiode sensitivity $\sigma_p$ by
       bumping the cantilever tip on the substrate surface.  In the
       first panel, the blue dots are experimental data, the green line
@@ -150,7 +150,7 @@ vibrations are configurable (with \hFconfig,
 \begin{figure}
   \begin{center}
     \subfloat[][]{\label{fig:calibcant:vibration:offset}
-      \includegraphics[width=0.8\textwidth]{figures/calibcant/vibration.png}}
+      \includegraphics[width=0.8\textwidth]{figures/calibcant/vibration}}
     \caption{\protect\subref{fig:calibcant:vibration:offset}Measuring
       the cantilever's thermal vibration.  The top panel shows the raw
       time series data in bins, the middle panel shows the
@@ -172,7 +172,7 @@ vibrations are configurable (with \hFconfig,
   \ContinuedFloat
   \begin{center}
     \subfloat[][]{\label{fig:calibcant:vibration:no-offset}
-      \includegraphics[width=0.8\textwidth]{figures/calibcant/vibration-no-offset.png}}
+      \includegraphics[width=0.8\textwidth]{figures/calibcant/vibration-no-offset}}
     \caption{\protect\subref{fig:calibcant:vibration:no-offset}This is
       the same data as in
       \protect\subref{fig:calibcant:vibration:offset} fit with
diff --git a/src/introduction/main.tex b/src/introduction/main.tex
index 17dfcf8..a5f6020 100644
--- a/src/introduction/main.tex
+++ b/src/introduction/main.tex
@@ -48,7 +48,7 @@ remarkably difficult.
 
 \begin{figure}
   \begin{center}
-  \includegraphics[width=2in]{figures/biotin-streptavidin/1SWE.png}%
+  \includegraphics[width=2in]{figures/biotin-streptavidin/1SWE}%
   \caption{Complex of biotin\index{biotin} (red) and a
     streptavidin\index{streptavidin} tetramer (green)
     (\href{http://dx.doi.org/10.2210/pdb1swe/pdb}{PDB ID: 1SWE})%
diff --git a/src/pyafm/frameworks.tex b/src/pyafm/frameworks.tex
index f95543c..2f0d5cf 100644
--- a/src/pyafm/frameworks.tex
+++ b/src/pyafm/frameworks.tex
@@ -66,7 +66,7 @@ reuse existing code to address similar tasks.
 \begin{figure}
   \begin{center}
     \includegraphics[width=0.8\textwidth]{%
-      figures/binary/pulling_chan_1_2d22.png}
+      figures/binary/pulling_chan_1_2d22}
     \caption{An excerpt from the main frame of the LabVIEW stack.
       This frame codes for the velocity-clamped pull phase of a
       push--bind--pull experiment.\label{fig:labview}}
-- 
2.26.2