From: David Schleef Date: Sun, 27 May 2001 23:54:24 +0000 (+0000) Subject: Don't see a need to keep these around. Pull them from the X-Git-Tag: r0_7_59~8 X-Git-Url: http://git.tremily.us/?a=commitdiff_plain;h=7145cae91d1d97752fc9680247ad4c84bf732ced;p=comedi.git Don't see a need to keep these around. Pull them from the attic if you want them. --- diff --git a/comedi/old/atmio-16f.c b/comedi/old/atmio-16f.c deleted file mode 100644 index 4829992c..00000000 --- a/comedi/old/atmio-16f.c +++ /dev/null @@ -1,528 +0,0 @@ -/* - module/ni_F.c - hardware driver for National Instruments AT-MIO-16F - - COMEDI - Linux Control and Measurement Device Interface - Copyright (C) 1995 Claus Schroeter - Copyright (C) 1999 David A. Schleef - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - -*/ - -/* - This driver is an adaptation of one written by clausi -*/ - -#include -#include -#include -#include - -#define ATMIO16F_SIZE 16 - -#define Command_Register_1 0x00 /* wo */ -#define Command_Register_2 0x02 /* wo */ -#define Command_Register_3 0x04 /* wo */ -#define Command_Register_4 0x06 /* wo */ -#define Status_Register_1 0x18 /* ro */ -#define Status_Register_2 0x1a /* ro */ - -#define ADC_FIFO_Register 0x00 /* ro */ -#define CONFIGMEM_Register 0x08 /* wo */ - -#define DAC0_Register 0x10 /* wo */ -#define DAC1_Register 0x12 /* wo */ - -#define CONFIGMEMCLR_Register 0x1b /* ro 8 */ -#define CONFIGMEMLD_Register 0x1b /* wo 8 */ -#define DAQ_Clear_Register 0x19 /* ro 8 */ -#define DAQ_Start_Register 0x1d /* ro 8 */ -#define Single_Conversion_Register 0x1d /* wo 8 */ -#define ADC_Calibration_Register 0x1f /* wo 8 */ - -#define TMRREQ_Clear_Register 0x1f /* ro 8 */ -#define DAC_Update_Register 0x18 /* wo */ -#define DAC_Clear_Register 0x1e /* ro 8 */ - -#define DMA_Channel_Clear_Register 0x0b /* ro 8 */ -#define DMATCA_Clear_Register 0x19 /* wo 8 */ -#define DMATCB_Clear_Register 0x09 /* ro 8 */ -#define External_Strobe_Register 0x1e /* wo 8 */ -#define Calibration_DAC_0_Load_Register 0x0a /* wo 8 */ -#define Calibration_DAC_1_Load_Register 0x1a /* wo 8 */ - -#define Am9513A_Data_Register 0x14 /* rw */ -#define Am9513A_Command_Register 0x16 /* wo */ -#define Am9513A_Status_Register 0x16 /* ro */ - -#define Digital_Input_Register 0x1c /* ro */ -#define Digital_Output_Register 0x1c /* wo */ - -#define RTSI_Switch_Shift_Register 0x0c /* wo 8 */ -#define RTSI_Switch_Strobe_Register 0x0e /* wo 8 */ - - -#define EEPROMCS _bit15 -#define SDATA _bit14 -#define SCLK _bit13 -#define SCANDIV _bit12 -#define INTGATE _bit10 -#define RETRIG_DIS _bit9 -#define DAQEN _bit8 -#define SCANEN _bit7 -#define SCN2 _bit6 -#define CNT32 _bit5 -#define RTSITRIG _bit4 - -#define A4RCV _bit15 -#define A4DRV _bit14 -#define A2RCV _bit13 -#define A2DRV _bit12 -#define BIPDAC1 _bit11 -#define BIPDAC0 _bit10 -#define EXTREFDAC1 _bit9 -#define EXTREFDAC0 _bit8 -#define EISA_DMA _bit7 -#define DMACHBB _bits543 -#define DMACHAB _bits210 - - - -/* stuff i don't know */ -#define MIO_ADCLR 0 -#define BIPOLAR 0 -#define DIFF 0 -#define MIO_SCONV 0 -#define MIO_SR 0 -#define FIFOEF 0 -#define MIO_ADFIFO 0 -#define mio_reset_bitcmd(a,b) /* */ -#define mio_set_bitcmd(a,b) /* */ - - - -#define DB_ERROR (1<<0) -#define DB_OVERFLOW (1<<1) -#define DB_HALF (1<<2) -#define DB_EMPTY (1<<3) - -#define DAQ_RUNNING (1<<0) -#define DAQ_DACUP (1<<1) -#define DAQ_SCONV (1<<2) -#define DAQ_BIPOLAR (1<<3) -#define DAQ_DIFF (1<<4) -#define DAQ_SYNC (1<<5) - - -typedef struct { - int adc; - int dac0; -} AdcVal; - -typedef struct{ - int DaqMode; - int CurrentDac; - int WgenStat; - int admode[16]; -}ni_F_private; -#define devpriv ((ni_F_private *)dev->private) - -int atmio16f_rem(comedi_device *dev); - -#if 0 -static void mio_SetDaqMode(int mode) -{ - devpriv->DaqMode = mode; -} -#endif - -/**********************************************************************/ -static int atmio16f_ai(comedi_device * dev, comedi_subdevice *s, comedi_trig * it) -{ - int chan,aref,range; - int i; - - chan=CR_CHAN(it->chanlist[0]); - range=CR_RANGE(it->chanlist[0]); - aref=CR_AREF(it->chanlist[0]); - - outw(0x00, dev->iobase + MIO_ADCLR); - - /* set ADC UNIPOLAR/BIPOLAR mode */ - if (range) - mio_reset_bitcmd(BIPOLAR, 0); - else - mio_set_bitcmd(BIPOLAR, 0); - - /* set ADC DIFF/RSE mode */ - if (aref) /* XXX check */ - mio_set_bitcmd(DIFF, 0); - else - mio_reset_bitcmd(DIFF, 0); - - outw(0x00, dev->iobase + MIO_SCONV); - - /* poll status register */ - for(i=0;i<25;i++){ - if( inw(dev->iobase + MIO_SR) & FIFOEF ) - break; - udelay(5); - } - if(i==25){ - comedi_error(dev,"timeout"); - return -ETIME; - } - - /* read value */ - it->data[0] = inw(dev->iobase + MIO_ADFIFO); - - return 1; -} - - -#if 0 -/*********************************************************************** - * - * Doublebuffer FIFO mechanism - * - */ - -#define MAX_DBUFSIZE 1024 - -struct wait_queue *DaqWait = NULL; -struct semaphore DaqSem = MUTEX; - - -unsigned int DblBuf[2][MAX_DBUFSIZE + 1]; - -unsigned int DblBufState = 0; - -unsigned int ActualReadCount = 0; -unsigned int ActualWriteCount = 0; -unsigned int ActualResidue = 0; - -unsigned int ActualWrite = 0; -unsigned int ActualRead = 0; - -/***********************************************************************/ -void mio_DaqInit(void) -{ - - DblBufState = 0; - ActualResidue = 0; - ActualWriteCount = 0; - ActualReadCount = 0; - - ActualRead = 0; - ActualWrite = 0; - DaqMode = 0; - - /*clear A/D circuit */ - outw(0x0000, MIO_ADCLR); - -} - - -/**********************************************************************/ -void mio_SwapWrite(void) -{ - ActualWrite = (ActualWrite ? 0 : 1); - DBGprint(DBG_DATA, ("Swapped Write to %d", ActualWrite)); - ActualWriteCount = 0; - if (ActualResidue >= (2 * MAX_DBUFSIZE)) { /* overflow buffer bit set */ - DBGprint(DBG_DATA, ("Buffer Overflow")); - DblBufState |= (DB_ERROR | DB_OVERFLOW); - } -} - -/**********************************************************************/ -void mio_SwapRead(void) -{ - ActualRead = (ActualRead ? 0 : 1); - DBGprint(DBG_DATA, ("Swapped Read to %d", ActualRead)); - ActualReadCount = 0; -} - -/**********************************************************************/ -void mio_AddDBuf(unsigned int val) -{ - if (ActualWriteCount < MAX_DBUFSIZE) { - DblBuf[ActualWrite][ActualWriteCount] = val; - ActualWriteCount++; - ActualResidue++; - } else { - mio_SwapWrite(); - } - if (ActualResidue >= MAX_DBUFSIZE) { - DblBufState |= DB_HALF; - if (DaqMode & DAQ_SYNC) - wake_up_interruptible(&DaqWait); - } -} - -/**********************************************************************/ -unsigned int mio_GetDBuf(void) -{ - unsigned int ret = 0; - - if (ActualResidue > 0) { - if (ActualReadCount < MAX_DBUFSIZE) { - ret = DblBuf[ActualRead][ActualReadCount]; - ActualReadCount++; - ActualResidue--; - } else { - mio_SwapRead(); - } - if (ActualResidue < MAX_DBUFSIZE) - DblBufState &= ~DB_HALF; - } else { - ret = 0; - DblBufState |= DB_EMPTY; - } - - DBGprint(DBG_DATA, ("residue=%d", ActualResidue)); - return ret; -} - -/**********************************************************************/ -int mio_SyncRead(int *buf, int count) -{ - int retval, i; - int dummy; - char *tbuf; - - - if (retval = verify_area(VERIFY_WRITE, buf, count)) - return retval; - - - if (DblBufState & DB_EMPTY) { - DBGprint(DBG_DATA, ("Buffer Empty")); - return -EINTR; - } - if (!(DblBufState & DB_HALF) && (DaqMode & DAQ_RUNNING)) { - DBGprint(DBG_DATA, ("\nWaiting for DB_HALF")); - DaqMode |= DAQ_SYNC; - interruptible_sleep_on(&DaqWait); - DaqMode &= ~DAQ_SYNC; - DBGprint(DBG_DATA, ("\nGot DB_HALF")); - } - if (DblBufState & DB_OVERFLOW) { - DBGprint(DBG_DATA, ("Double Buffer Overflow")); - return -EOVERFLOW; - } - /* copy block to FS */ - for (i = 0; i < count && i < ActualResidue; i++) { - dummy = mio_GetDBuf(); - DBGprint(DBG_DATA, ("buf=%d", dummy)); - if (DblBufState & DB_EMPTY) { - DBGprint(DBG_DATA, ("count=%d", i)); - return i; - } - put_fs_long(dummy, (int *) &(buf[i])); - /*memcpy_tofs((int *) buf, &dummy ,sizeof(int)); */ - } - - return count; - -} - -/**********************************************************************/ -void mio_DaqFinish(void) -{ - - DaqMode &= ~DAQ_RUNNING; - if (DaqMode & DAQ_SYNC) - wake_up_interruptible(&DaqWait); -} - -/**********************************************************************/ -void mio_DaqStart(int mode) -{ - - DBGprint(DBG_DATA, ("mode (0x%x)", mode)); - - mio_DaqInit(); - - DaqMode |= (DAQ_RUNNING | mode); - - /*clear A/D circuit */ - outw(0x0000, MIO_ADCLR); - - /* set ADC UNIPOLAR/BIPOLAR mode */ - if (DaqMode & DAQ_BIPOLAR) - mio_reset_bitcmd(BIPOLAR, 0); - else - mio_set_bitcmd(BIPOLAR, 0); - - /* set ADC DIFF/RSE mode */ - if (DaqMode & DAQ_DIFF) - mio_set_bitcmd(DIFF, 0); - else - mio_reset_bitcmd(DIFF, 0); - - if (DaqMode & DAQ_SCONV) { - DBGprint(DBG_DATA, ("trigger conversion")); - outw(0x00, MIO_SCONV); /* trigger first value */ - while (!(inw(MIO_SR) & FIFOEF)); /* sync FIFOEF */ - } - if (DaqMode & DAQ_DACUP) - printk("WGEN MODE\n"); - -} - -/***********************************************************************/ -void mio_DaqIRQ(int status) -{ - comedi_sample s; - - if (DaqMode & DAQ_RUNNING) { - - /* read FIFO content into Buffer */ - s.chan = dev->adchan; - s.job = dev->job; - while (inw(MIO_SR) & FIFOEF) { - - it->data = inw(dev->iobase + MIO_ADFIFO); - - } - - /* trigger next conversion */ - if (DaqMode & DAQ_SCONV) { - outw(0x0000, dev->iobase + MIO_SCONV); - } - if ((DaqMode & DAQ_DACUP) && !(WgenStat & WGEN_RUNNING)) { -#if DEBUG - if (dbgMask) - printk("Finish DACUP DAQ Cycle\n"); -#endif - DaqMode &= ~DAQ_RUNNING; - while (!(inw(MIO_SR) & FIFOEF)); /* poll status */ - val = inw(MIO_ADFIFO) | (CurrentDac << 16); - mio_AddDBuf(val); - - if (DaqMode & DAQ_SYNC) - wake_up_interruptible(&DaqWait); - } - } else - printk("DAQ-INTERRUPT unknown status (0x%x)", status); - -} - -#endif - -int atmio16f_ao(comedi_device *dev,comedi_subdevice *s,comedi_trig *it) -{ - return -EINVAL; -} - -int atmio16f_di(comedi_device *dev,comedi_subdevice *s,comedi_trig *it) -{ - return -EINVAL; -} - -int atmio16f_do(comedi_device *dev,comedi_subdevice *s,comedi_trig *it) -{ - return -EINVAL; -} - - -int atmio16f_init(comedi_device *dev,comedi_devconfig *it) -{ - int ret=0; - comedi_subdevice *s; - - if(strcmp(it->board_name,"at-mio-16f-5")) - return 0; - - dev->driver_name="atmio16f"; - dev->board_name="at-mio-16f"; - if(it->options[0]) - dev->iobase=it->options[0]; - else return -EINVAL; - - printk("comedi: atmio16f: 0x%04x\n",dev->iobase); - if(check_region(dev->iobase,ATMIO16F_SIZE)<0){ - comedi_error(dev,"I/O port conflict"); - return -EIO; - } - request_region(dev->iobase,ATMIO16F_SIZE,"atmio16f"); - dev->iosize=ATMIO16F_SIZE; - - dev->n_subdevices=4; - - if((ret=alloc_subdevices(dev))<0) - goto cleanup; - if((ret=alloc_private(dev,sizeof(ni_F_private)))<0) - goto cleanup; - - s=dev->subdevices+0; - /* ai subdevice */ - s->type=COMEDI_SUBD_AI; - s->subdev_flags=SDF_READABLE; - s->n_chan=16; - s->maxdata=0xfff; - s->range_type=RANGE_unknown; - s->trig[0]=atmio16f_ai; - - s++; - /* ao subdevice */ - s->type=COMEDI_SUBD_AO; - s->subdev_flags=SDF_WRITEABLE; - s->n_chan=2; - s->maxdata=0xfff; - s->range_type=RANGE_unknown; - s->trig[0]=atmio16f_ao; - - s++; - /* di subdevice */ - s->type=COMEDI_SUBD_DI; - s->subdev_flags=SDF_READABLE; - s->n_chan=8; - s->maxdata=1; - s->range_type=RANGE_digital; - s->trig[0]=atmio16f_di; - - s++; - /* do subdevice */ - s->type=COMEDI_SUBD_DO; - s->subdev_flags=SDF_WRITEABLE; - s->maxdata=1; - s->n_chan=8; - s->range_type=RANGE_digital; - s->trig[0]=atmio16f_do; - - /* do some init */ - - dev->rem=atmio16f_rem; - - return 1; -cleanup: - atmio16f_rem(dev); - - return ret; -} - - -int atmio16f_rem(comedi_device *dev) -{ - - if(dev->iobase) - release_region(dev->iobase,dev->iosize); - - return 0; -} - diff --git a/comedi/old/atmio-16x.c b/comedi/old/atmio-16x.c deleted file mode 100644 index c8ec0ebd..00000000 --- a/comedi/old/atmio-16x.c +++ /dev/null @@ -1,193 +0,0 @@ -/* - module/atmio-16x.c - hardware driver for National Instruments AT-MIO-16X - - COMEDI - Linux Control and Measurement Device Interface - Copyright (C) 1998 David A. Schleef - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - -*/ - -/* - specifications are found in NI document 320640b.pdf -*/ - -#define Command_Register_1 0x00 /* wo */ -#define Command_Register_2 0x02 /* wo */ -#define Command_Register_3 0x04 /* wo */ -#define Command_Register_4 0x06 /* wo */ -#define Status_Register_1 0x18 /* ro */ -#define Status_Register_2 0x1a /* ro */ - -#define ADC_FIFO_Register 0x00 /* ro */ -#define CONFIGMEM_Register 0x08 /* wo */ - -#define DAC0_Register 0x10 /* wo */ -#define DAC1_Register 0x12 /* wo */ - -#define CONFIGMEMCLR_Register 0x1b /* ro 8 */ -#define CONFIGMEMLD_Register 0x1b /* wo 8 */ -#define DAQ_Clear_Register 0x19 /* ro 8 */ -#define DAQ_Start_Register 0x1d /* ro 8 */ -#define Single_Conversion_Register 0x1d /* wo 8 */ -#define ADC_Calibration_Register 0x1f /* wo 8 */ - -#define TMRREQ_Clear_Register 0x1f /* ro 8 */ -#define DAC_Update_Register 0x18 /* wo */ -#define DAC_Clear_Register 0x1e /* ro 8 */ - -#define DMA_Channel_Clear_Register 0x0b /* ro 8 */ -#define DMATCA_Clear_Register 0x19 /* wo 8 */ -#define DMATCB_Clear_Register 0x09 /* ro 8 */ -#define External_Strobe_Register 0x1e /* wo 8 */ -#define Calibration_DAC_0_Load_Register 0x0a /* wo 8 */ -#define Calibration_DAC_1_Load_Register 0x1a /* wo 8 */ - -#define Am9513A_Data_Register 0x14 /* rw */ -#define Am9513A_Command_Register 0x16 /* wo */ -#define Am9513A_Status_Register 0x16 /* ro */ - -#define Digital_Input_Register 0x1c /* ro */ -#define Digital_Output_Register 0x1c /* wo */ - -#define RTSI_Switch_Shift_Register 0x0c /* wo 8 */ -#define RTSI_Switch_Strobe_Register 0x0e /* wo 8 */ - -#define _B(b) ((struct bitchan){_B_CHAN,(b)}) - -#define _B_CHAN Command_Register_1 -#define EEPROMCS _bit15 -#define SDATA _bit14 -#define SCLK _bit13 -#define SCANDIV _bit12 -#define INTGATE _bit10 -#define RETRIG_DIS _bit9 -#define DAQEN _bit8 -#define SCANEN _bit7 -#define SCN2 _bit6 -#define CNT32 _bit5 -#define RTSITRIG _bit4 -#undef _B_CHAN - -#define _B_CHAN Command_Register_2 -#define A4RCV _bit15 -#define A4DRV _bit14 -#define A2RCV _bit13 -#define A2DRV _bit12 -#define BIPDAC1 _bit11 -#define BIPDAC0 _bit10 -#define EXTREFDAC1 _bit9 -#define EXTREFDAC0 _bit8 -#define EISA_DMA _bit7 -#define DMACHBB _bits543 -#define DMACHAB _bits210 -#undef _B_CHAN - -#define _B_CHAN Command_Register_3 -#define ADCDSP _bit15 -#define DIOPBEN _bit14 -#define DIOPAEN _bit13 -#define DMATCINT _bit12 -#define DACCMPLINT _bit11 -#define DAQCMPLINT _bit10 -#define IO_INT _bit9 -#define DMACHA _bit8 -#define DMACHB _bit7 -#define ARCREQ _bit6 -#define DAC1REQ _bit5 -#define DAC0REQ _bit4 -#define DRVAIS _bit3 -#define INTCHB2 _bit2 -#define INTCHB1 _bit1 -#define INTCHB0 _bit0 -#undef _B_CHAN - -#define _B_CHAN Command_Register_3 -#define CLKMODEB1 _bit15 -#define CLKMODEB0 _bit14 -#define DAC1DSP _bit13 -#define DAC0DSP _bit12 -#define DACMB3 _bit11 -#define DACMB2 _bit10 -#define DACMB1 _bit9 -#define DACMB0 _bit8 -#define DACGATE _bit7 -#define DB_DIS _bit6 -#define CYCLICSTOP _bit5 -#define ADCFIFOREQ _bit4 -#define SRC3SEL _bit3 -#define GATE2SEL _bit2 -#define FIFODAC _bit1 -#define EXTTRIG_DIS _bit0 -#undef _B_CHAN - -#define _B_CHAN Status_Register_1 -#define DAQCOMP _bit15 -#define DAQPROG _bit14 -#define ADCFIFOHF _bit13 -#define ADCFIFOEF _bit12 -#define DMATCA _bit11 -#define DMATCB _bit10 -#define OVERFLOW _bit9 -#define OVERRUN _bit8 -#define TMRREQ _bit7 -#define DACCOMP _bit6 -#define DACFIFOFF _bit5 -#define DACFIFOHF _bit4 -#define DACFIFOEF _bit3 -#define EEPROMDATA _bit2 -#define EEPROMCD _bit1 -#define CFGMEMEF _bit0 -#undef _B_CHAN - -#define _B_CHAN -#define ADC_BUSY _bit0 -#undef _B_CHAN - -#define _B_CHAN CONFIGMEM_Register -#define CHAN_SE _bit15 -#define CHAN_AIS _bit14 -#define CHAN_CAL _bit13 -#define CHAN_BIP _bit12 -#define CHANSEL3 _bit9 -#define CHANSEL2 _bit8 -#define CHANSEL1 _bit7 -#define CHANSEL0 _bit6 -#define CH_GAIN2 _bit5 -#define CH_GAIN1 _bit4 -#define CH_GAIN0 _bit3 -#define CHAN_LAST _bit2 -#define CHAN_GHOST _bit1 -#define CHAN_DSP _bit0 -#endif _B_CHAN - - - - - - - - - - -int irqbits[]={ - -1, -1, -1, 0, 1, 2, -1, 3, - -1, -1, 4, 5, 6, -1, -1, 7 -} - - - - diff --git a/comedi/old/rti860.c b/comedi/old/rti860.c deleted file mode 100644 index 0ab08d56..00000000 --- a/comedi/old/rti860.c +++ /dev/null @@ -1,1264 +0,0 @@ -/***************************************************************** - Linux device driver for RTI860 hardware - - Copyright (C) 1995 Ralf Haller - (C) 1995, 1996 Harald Kirsch (kir@iitb.fhg.de) - - Fraunhofer Institut für - Informations- und Datenverarbeitung (IITB) - Fraunhoferstr. 1 - 76131 Karlsruhe - -*****************************************************************/ -/* - * values for ioctl - */ -#define RTI860_SET_PAR 1 -#define RTI860_GET_PAR 2 -#define RTI860_START 3 -#define RTI860_RESET 4 - -/* - * flags - */ -#define RTI860_F_PRESENT (1<<0) -#define RTI860_F_OPEN (1<<1) -#define RTI860_F_BUSY (1<<2) -#define RTI860_F_IRQ (1<<3) -#define RTI860_F_RESTART (1<<4) - -/* The following flag(s) can be changed by the user */ -#define RTI860_F_USER (RTI860_F_RESTART) - -typedef enum { - Channel16 =-16, - Channel15 =-15, - Channel14 =-14, - Channel13 =-13, - Channel12 =-12, - Channel11 =-11, - Channel10 =-10, - Channel9 =-9, - Channel8 =-8, - Channel7 =-7, - Channel6 =-6, - Channel5 =-5, - Channel4 =-4, - Channel3 =-3, - Channel2 =-2, - Channel1 =-1, - Channel1_4 = 0, - Channel5_8 = 1, - Channel9_12 = 2, - Channel13_16 = 3, - Channel1_16 = 4, - Channel1_8 = 5, - Channel9_16 = 6 -} Channel; - -typedef enum { - Free = 0, - BereichPlus = 1, - BereichMinus = 2, - PegelPlus = 3, - PegelMinus = 4, - TTLTrigger = 5 -} Trigger; - -/* - * parameter struct used for ioctl - */ -struct rti860_t -{ - unsigned int flags; /* flags */ - unsigned int base; /* base address */ - short channel; /* channels to scan, see enum above */ - unsigned short trigger; /* trigger mode, see enum above */ - signed char level; /* trigger level, a value between -128 - and 127 */ - int tics; /* >0: use the 5MHz internal clock with - ticks as the divider. - <0: use the external clock with ticks - as the divider. - In both cases the sampling frequency - is 1.0/(ticks*base_frequency) */ - int irq; /* interrupt channel, 0 if none */ - unsigned timeout; /* timeout in seconds */ - unsigned sleep_time; /* sleep time in polling mode in jiffies - */ -}; - -typedef struct rti860_t Rti860; - -#define F2TICS(f) (5e6/(f)) -#define TICS2F(tics) (5e6/(tics)) -/***************************************************************** - Linux device driver for RTI860 hardware - - Copyright (C) 1995 Ralf Haller - (C) 1995, 1996 Harald Kirsch (kir@iitb.fhg.de) - - Fraunhofer Institut für - Informations- und Datenverarbeitung (IITB) - Fraunhoferstr. 1 - 76131 Karlsruhe - -*****************************************************************/ - - -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include "rti860.h" - -/* major device number for rti860 device */ -#define RTI860_MAJOR 58 -/* IMPORTANT: check MAX_CHRDEV in major.h (MAX_CHRDEV >= RTI860_MAJOR) */ - -/* maximum number of minors */ -#define RTI860_NO 24 -#define RTI860_MAX 5 - -/* size of internal memory (256k) */ -#define RTI860_MEMSIZE 0x00040000L -#define RTI860_MEMCHUNK RTI860_MEMSIZE / 32 - -/* minimal and maximal 200ns-tics */ -#define RTI860_MAX_TICS 655350000 -#define RTI860_MIN_TICS 25 /* 200kHz */ - -#define INDEX(a) (minor_index[a]) -#define SEC2JIFFY(a) ((a)*HZ) -#define TICS2USEC(a) ((a)/5) /* one tic is 200ns */ - - - -/* delay for hardware im ms */ -#define delay(a) __delay(a*loops_per_msec) - -/* - * hardware registers - */ -#define status_reg ((rti860[INDEX(minor)].base) + 0x00) -#define control_reg ((rti860[INDEX(minor)].base) + 0x02) -#define muxdata_reg ((rti860[INDEX(minor)].base) + 0x04) -#define softcon_reg ((rti860[INDEX(minor)].base) + 0x06) -#define adcdata_reg ((rti860[INDEX(minor)].base) + 0x08) -#define adcmem_reg ((rti860[INDEX(minor)].base) + 0x0A) -#define datamem_reg ((rti860[INDEX(minor)].base) + 0x0C) -#define hostmem_reg ((rti860[INDEX(minor)].base) + 0x0E) -#define adchstmem_reg ((rti860[INDEX(minor)].base) + 0x10) -#define muxmemscan_reg ((rti860[INDEX(minor)].base) + 0x12) -#define data9513_reg ((rti860[INDEX(minor)].base) + 0x14) -#define ctrl9513_reg ((rti860[INDEX(minor)].base) + 0x16) -#define flgsclr_reg ((rti860[INDEX(minor)].base) + 0x18) -#define trigger_reg ((rti860[INDEX(minor)].base) + 0x1A) -#define indaddr_reg ((rti860[INDEX(minor)].base) + 0x1C) - -/* - * NB. we must include the kernel idenfication string to install the module. - */ -#include -static char kernel_version[] = UTS_RELEASE; - -/* parameters for all possible rti860s, can be changed with ioctl */ -static Rti860 rti860[RTI860_MAX] = -{{0,0L,Channel1_4,Free,0,5000,0,5,10}, /* default */ - {0,0L,Channel1_4,Free,0,5000,0,5,10}, - {0,0L,Channel1_4,Free,0,5000,0,5,10}, - {0,0L,Channel1_4,Free,0,5000,0,5,10}, - {0,0L,Channel1_4,Free,0,5000,0,5,10}}; - -static void rti860_timer( unsigned long ); - -/* timer for polling mode */ -static struct timer_list timer[RTI860_MAX] = -{{NULL,NULL,0,0,rti860_timer}, - {NULL,NULL,0,1,rti860_timer}, - {NULL,NULL,0,2,rti860_timer}, - {NULL,NULL,0,3,rti860_timer}}; - -/* index to rti860-struct */ -static int minor_index[RTI860_NO]={0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0}; - -/* number of channels for rti860.channel */ -/* static int num_channels[]={4,4,4,4,16,8,8}; */ - -/* wait queue for rti860 device driver */ -static struct wait_queue *rti860_wait_q; - -/* irq counts */ -static unsigned short irq_count[16]={0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0}; - -/* number of delay loops per msec */ -static int loops_per_msec; - -/***** - Der folgende Typ beschreibt ein Counter Mode Register des 9513. Die - Bits sind in dieser merkwürdigen Reihenfolge, weil der 80x86 die - lo-Bytes bei niedrigen Adressen abspeichert. -*****/ -typedef struct s_CounterMode { - unsigned output:3; - unsigned increm:1; - unsigned bcdCount:1; - unsigned repeat:1; - unsigned reloadFrom:1; - unsigned specialGate:1; - unsigned source:4; - unsigned sourceEdge:1; - unsigned gate:3; -} CounterMode; -#define cm2us(x) (* (unsigned short*)&(x) ) - -#if 0 -/**************************************************************************** - * read one counter of the 9513 - ****************************************************************************/ -static void read_counter( unsigned int minor, unsigned *c ) -{ - - int i; - - /***** 9513 in 16-bit mode */ - outw(0xFFEF, ctrl9513_reg); - - /***** Copy to hold register */ - outw(0xFFA0+0x1F, ctrl9513_reg); - - /***** Select the first counter */ - outw(0xFF19, ctrl9513_reg); - - for( i=0 ; i<5 ; i++ ) { - - /***** Read the counter */ - c[i] = inw(data9513_reg); /* hold register */ -} -} -#endif - -/**************************************************************************** - * reset the 9513 - ****************************************************************************/ -static void reset9513( unsigned int minor ) -{ - outw( 0x0000, control_reg ); /* Control-register zurücksetzen */ - delay(1); - /**** 9513 zweimal zurücksetzen */ - outw( 0xFFFF, ctrl9513_reg ); delay(1); - outb( 0xFF, ctrl9513_reg ); delay(1); - - /***** - Betriebsart setzen, d.h. Master-Mode Register adressieren und dann - den Wert 0x3100 als zwei einzelne Bytes ausgeben. Der Mode 0x3100 - bedeutet: - ---Bitpositionen--- ----eingestellte Funktion bei 0x3100---- - 1000 0000 0000 0000 : Frequenzscalierung binär (nicht BCD) - 0100 0000 0000 0000 : automatisches Adreßincrement - 0010 0000 0000 0000 : 16-bit Datenbus (ab sofort) - 0001 0000 0000 0000 : FOUT Aus - 0000 1111 0000 0000 : FOUT Divider = Division durch 1 - 0000 0000 1111 0000 : FOUT-Quelle ist E1 - 0000 0000 0000 1100 : Comparator 1 und 2 aus - 0000 0000 0000 0000 : Keine Funktion als Uhr (time-of-day) - *****/ - outb( 0x17, ctrl9513_reg ); delay(1); - outb( 0x00, data9513_reg ); delay(1); - outb( 0x31, data9513_reg ); delay(1); - - /***** - Zähler 1 wird initialisiert: - 0x0005 heißt: kein Gating, zähle steigende Flanke, zähle Ausgang - von Zähler 0 (?), kein special gate, nachladen vom Loadregister, - einmal zählen, binär zählen, abwärts zählen, active low terminal - count pulse - *****/ - outw( 0xFF01, ctrl9513_reg ); delay(1); - outw( 0x0005, data9513_reg ); delay(1); - - /* Eine A/D-Wandlung auslösen (warum?) */ - outw( 0x1234, softcon_reg ); delay(1); - - /***** - Zähler 1 erneut initialisieren. (warum?) - 0x0002 wie oben, außer Ausgabe auf 'terminal count toggled'. - Anschließend wird der Ausgabepin definiert auf 0 gesetzt. - *****/ - outw( 0xFF01, ctrl9513_reg ); delay(1); - outw( 0x0002, data9513_reg ); delay(1); - outw( 0xFFE1, ctrl9513_reg ); delay(1); - - /***** - Zähler 3 identisch mit Zähler 1 initialisieren. Ausgabepin auf 1, da - bei 0 die A/D-Wandlung angehalten wird: DONE-Signal. - *****/ - outw( 0xFF03, ctrl9513_reg ); delay(1); - outw( 0x0002, data9513_reg ); delay(1); - outw( 0xFFE3, ctrl9513_reg ); delay(1); - - /***** - Zähler 5 identisch mit Zähler 1 initialisieren. - *****/ - outw( 0xFF05, ctrl9513_reg ); delay(1); - outw( 0x0002, data9513_reg ); delay(1); - outw( 0xFFE5, ctrl9513_reg ); delay(1); - - /* Kontrollregister zurücksetzen */ - outw( 0x0000, control_reg ); delay(1); -} - -/**************************************************************************** - * set the trigger - ****************************************************************************/ -static void init_overflow_counter( unsigned int minor ) -/***** - Zähler 4 und 5 auf dem 9513 sind wohl dazu gedacht, die - Speicherüberlaufbits anzutreiben (vgl. RTI860-Handbuch S.4-10 und - S.B-13). Beide werden hier initialisiert, so daß nach der halben - Speichergröße jeweils ein positiver Puls am pin O5 des 9513 - ausgegeben wird. Zähler 4 lassen wir bis 4 zählen. Damit treibt - er Zähler 5, den wir jeweils bis 0x8000 zählen lassen, so daß insgesamt - bis 2^17 = halbe Speichergröße der RTI860 gezählt wird. -*****/ -{ - CounterMode mode; - - /***** Zähler 4 und 5 abschalten */ - outw(0xFFC0 + (1<<(5-1)) + (1<<(4-1)), ctrl9513_reg); delay(1); - - /***** Zähler 4 */ - mode.gate = 0; - mode.sourceEdge = 0; - mode.source = 4; - mode.specialGate = 0; - mode.reloadFrom = 0; - mode.repeat = 1; - mode.bcdCount = 0; - mode.increm = 0; - mode.output = 1; - outw( 0xFF04, ctrl9513_reg ); delay(1); - outw( cm2us(mode), data9513_reg ); delay(1); /* Mode */ - outw( 0x0004, data9513_reg ); delay(1); /* Loadregister */ - outw( 0x0000, data9513_reg ); delay(1); /* Holdregister */ - outw( 0xFF48, ctrl9513_reg ); delay(1); /* Lade von Loadregister */ - - /***** Zähler 5 wird von Zähler 4 betrieben */ - mode.gate = 0; - mode.sourceEdge = 0; - mode.source = 0; - mode.specialGate = 0; - mode.reloadFrom = 0; - mode.repeat = 1; - mode.bcdCount = 0; - mode.increm = 0; - mode.output = 1; - outw( 0xFF05, ctrl9513_reg ); delay(1); - outw( cm2us(mode), data9513_reg ); delay(1); /* Mode */ - outw( 0x8000, data9513_reg ); delay(1); /* Loadregister */ - outw( 0x0000, data9513_reg ); delay(1); /* Holdregister */ - outw( 0xFF50, ctrl9513_reg ); delay(1); /* Lade von Loadregister */ -} - -/*****************************************************************/ -static void -set_trigger(unsigned int minor) - -{ - static unsigned short masks[] = { - 0x000c, 0x0003, 0x0002, 0x0001, 0x0000, 0x0008 - }; - unsigned int mask; - - mask = masks[rti860[INDEX(minor)].trigger]; - mask |= (0x8000 + rti860[INDEX(minor)].level * 128) & 0xFF00; - outw(mask, trigger_reg); delay(5); -} - -/*****************************************************************/ -/* - Tell the board, which channels to scan. -*/ -static void -set_inputmux(unsigned int minor) -{ - unsigned short I; - unsigned base=8; - - outw( 0x0000, control_reg ); delay(1); - - if( rti860[INDEX(minor)].channel >= 0 ) { - switch( rti860[INDEX(minor)].channel ) { - case Channel1_16: - for (I = 0; I < 16; I++) { - outw(I, muxmemscan_reg ); delay(1); - outw(15-I, muxdata_reg); delay(1); - } - break; - case Channel1_8: - base = 0; - case Channel9_16: - for(I=0; I<16; I++) { - outw(I, muxmemscan_reg); delay(1); - outw((15-I)%8 + base, muxdata_reg); delay(1); - } - break; - case Channel1_4: - case Channel5_8: - case Channel9_12: - case Channel13_16: - outw( 0x0000, control_reg ); - for (I = 0; I<16; I++) { - outw(I, muxmemscan_reg); delay(1); - outw(((15-I) & 0x03) + (rti860[INDEX(minor)].channel << 2), - muxdata_reg); delay(1); - } - break; - default: - printk(KERN_DEBUG "Wrong mode in set_inputmux!\n"); - } - } else { - outw( 0x0000, control_reg ); - for(I = 0; I < 16; I++) { - outw(I, muxmemscan_reg); delay(1); - outw(-rti860[INDEX(minor)].channel-1, muxdata_reg); delay(1); - } - } - - /***** Set start of scan to the last mux-data register */ - outw(0x0F, muxmemscan_reg); delay(1); - delay(1); -} -/**************************************************************************** - * initialize counter 1 - ****************************************************************************/ -void -init_clock(unsigned int minor) -/***** - Zähler 1 des 9513 ist der Teiler entweder f"ur die interne clock, die - mit 5MHz l"auft, oder aber auch f"ur die externe clock. -*****/ -{ - unsigned scale, prescale; - unsigned mode; - /***** - Die folgenden Zeilen initialisieren Counter 1. Counter 1 - erzeugt den Takt für die A/D-Wandlung. - Der Modus=0x9025 + (Vorteiler+0x000B)<<8 - bedeutet (vgl. S.2-141 im Am9513-Handbuch): - Gating Control: active hi gate 1 1110 0000 0000 0000 - Source Edge: Count on Falling Edge 0001 0000 0000 0000 - Count Source: F_Vorteiler 0000 1111 0000 0000 - Special Gate: disabled 0000 0000 1000 0000 - Reload from: Load Register 0000 0000 0100 0000 - Repetitively: TRUE 0000 0000 0010 0000 - Count Type: binary 0000 0000 0001 0000 - Direction: count down 0000 0000 0000 1000 - Output: Active Lo Pulse 0000 0000 0000 0111 - Der Mode entspricht 'Mode E' S.2-131 im Handbuch. - *****/ - - if( rti860[INDEX(minor)].tics < 0 ) { - /* select SRC1 as counter input */ - mode = 0x9025 | (1<<8); - scale = -rti860[INDEX(minor)].tics; - } else { - for(prescale=0,scale=rti860[INDEX(minor)].tics; - scale > 65535; - prescale++,scale/=16); - /***** - Select F1...F5, i.e. a prescaler-output, as counter input - The available prescale values are 1, 16, 256, 4096 and 65536. - The value of prescale must be 0,1,2,3 or 4. - ****/ - mode = 0x9025 | ((prescale+0xB)<<8); - } - - outw( 0xFF01, ctrl9513_reg ); delay(1); /* address counter 1 */ - outw( mode, data9513_reg ); delay(1); /* set mode */ - outw( scale, data9513_reg ); delay(1); /* set load register */ - outw( 0x0000, data9513_reg ); delay(1); /* set hold register */ - outw( 0xFF41, ctrl9513_reg ); delay(1); /* load counter with load - register */ -} - -/**************************************************************************** - * initialize counter 2&3 - ****************************************************************************/ -static void init_posttrigger_counter( unsigned int minor ) -/***** - Zähler 2&3 zählt A/D-Wandlungen nach dem Trigger. Sobald 2&3 auf 0 - zählt, hört die RTI860 mit A/D-Wandlungen auf. Deshalb werden 2&3 - in RTI860_Start() bei kontinuierlichem Modus nicht scharfgemacht -*****/ -{ - /***** - Der Modus=0x1221 bedeutet (vgl. S.2-141 im Am9513-Handbuch): - Gating Control: No Gating 1110 0000 0000 0000 - Source Edge: Count on Falling Edge 0001 0000 0000 0000 - Count Source: SRC 2 0000 1111 0000 0000 - Special Gate: disabled 0000 0000 1000 0000 - Reload from: Load Register 0000 0000 0100 0000 - Repetitively: TRUE 0000 0000 0010 0000 - Count Type: binary 0000 0000 0001 0000 - Direction: count down 0000 0000 0000 1000 - Output: Active Hi Pulse 0000 0000 0000 0111 - Es stellt sich die Frage, warum das Loadregister gerade auf - samples-1 gesetzt wird, wenn sowieso kontinuierlich gearbeitet - wird. - *****/ - outw( 0xFF02, ctrl9513_reg ); delay(1); /* Adressieren */ - outw( 0x1221, data9513_reg ); delay(1); /* Modus setzen */ - outw( 333, data9513_reg ); delay(1); /* Loadregister */ - outw( 0x0000, data9513_reg ); delay(1); /* Holdregister */ - outw( 0xFF42, ctrl9513_reg ); delay(1); /* Counter:=Loadregister */ - - /***** - Counter 3 zählt zusammen mit Counter 2 die gewandelten Daten. Der - Output von Counter 3 ist sogar am Ausgabeport der RTI860 zu finden - --- als DONE-Signal. Außderdem hält die Karte tatsächlich an, - wenn der Ausgang von Counter 3 auf lo geht. - *****/ - outw( 0xFF03, ctrl9513_reg ); /* Source: Counter 3 - single count */ - delay(1); /* TC toggle */ - outw( 0x0002, data9513_reg ); /* Source: Counter 2 */ - delay(1); /* single count, TC toggle */ - outw( 0x0003, data9513_reg ); /* Loadregister = 3 */ - delay(1); - outw( 0x0000, data9513_reg ); /* Holdregister = 0 */ - delay(1); - outw( 0xFF44, ctrl9513_reg ); /* Load Counter 3 with Loadregister*/ - delay(1); - outw( 0xFFF3, ctrl9513_reg ); /* Counter 3 steppen erstes mal */ - delay(1); - outw( 0xFFF3, ctrl9513_reg ); /* zweites mal */ - delay(1); - outw( 0xFFF3, ctrl9513_reg ); /* drittes mal */ - delay(1); - outw( 0xFFE3|8, ctrl9513_reg ); /* Ausgang Counter 3 auf high */ - delay(1); - - /***** - Eine A/D-Wandlung auslösen, damit Flipflop U82 (S.6,Schaltplan) - auch sicher durchschaltet. - Die Methode hat letztlich doch nicht funktioniert. Deshalb wird - jetzt im reset9513 der Ausgang von counter 3 bereits auf High, statt - auf Low gesetzt. Das scheint zu funktionieren. - *****/ - /*outw( 0x1234, softcon_reg ); delay(1);*/ - } - -/*****************************************************************/ -/* - Clear the board memory -*/ -static void -rti860_clearmem( unsigned int minor ) -{ - int i; - /***** Setze ADC Zieladresse auf 0 */ - outw( 0x8100, adchstmem_reg ); delay(1); /* most sign. bits */ - outw( 0x8100, adchstmem_reg ); delay(1); - outw( 0x1000-20, adcmem_reg ); delay(1); /* least sign. bits */ - for(i=0; i<40; i++) { - outw( 0, control_reg ); - } - - outw( 0x8100, adchstmem_reg ); delay(1); /* most sign. bits */ - outw( 0x8100, adchstmem_reg ); delay(1); - outw( 0x0000, adcmem_reg ); delay(1); /* least sign. bits */ - - /***** Setze Leseadresse auf 0 */ - outw( 0x0001, adchstmem_reg ); delay(1); /* most sign. bits */ - outw( 0x0001, adchstmem_reg ); delay(1); - outw( 0x0000, hostmem_reg ); delay(1); /* least sign. bits */ -} -/*****************************************************************/ -/* - initialize the rti860 -*/ -static void -rti860_init( unsigned int minor ) -{ - - reset9513(minor); delay(5); - rti860_clearmem(minor ); - - set_inputmux(minor); - set_trigger(minor); -} - -/**************************************************************************** - * start the rti860 - ****************************************************************************/ -static void rti860_start( unsigned int minor ) -/***** - Startet die A/D-Wandlung auf der Karte mit den in RTI860_Init - vorgegebenen Parametern. Die A/D-Daten werden im Speicher der Karte - abgelegt. Wurde Betriebsart=Fix gewählt, so beendet die Karte - selbständig die Messung nach der vorgegebenen Anzahl der - Einzelmessungen. Andernfalls muß die Karte mit RTI860_Stop oder - RTI_860_Reset angehalten werden. - Hinweis: Diese Prozedur setzt den Speicher der Karte nicht zurück. -*****/ -{ - unsigned short control; - - reset9513(minor); - set_inputmux(minor); - set_trigger(minor); - - /***** Steuerwort der RTI860 setzen: */ - control = (1<<1) /* Memory Mode Enable */ - | (1<<2) /* Scan Mode Enable */ - | (1<<5); /* Continuous Transfer Mode Enable */ - - if( rti860[INDEX(minor)].channel >= 0 ) - control |= (1<<8); /* Simultaneous Mode Enable */ - - if( rti860[INDEX(minor)].irq > 0 ) { - control |= (1<<14); /* continuous transfer interrupt */ - control |= (1<<13); /* error interrupt */ - } - outw_p(control, control_reg); delay(1); - - init_posttrigger_counter(minor); - init_clock(minor); - init_overflow_counter(minor); - - rti860_clearmem( minor ); - - /***** - clear the overflow flags of the 9513, - in particular reset the DONE-bit. - *****/ - outw_p(0x0000, flgsclr_reg); delay(1); - outw_p(0x8000, flgsclr_reg); delay(1); - - /***** Zähler 1,4,5 scharfmachen */ - outw_p(0xFF39, ctrl9513_reg); delay(1); - - /***** Wandlung starten */ - outw_p(control|1, control_reg); delay(1); -} -/*****************************************************************/ -/* - Beendet die A/D-Wandlungen auf der Karte. Der Speicher der Karte - wird *nicht* gelöscht. Die Karte kann ohne Neuinitialisierung wieder - gestartet werden. -*/ -#if 0 -static void -rti860_stop( unsigned int minor ) -{ - reset9513( minor ); -} -#endif - -#ifdef PROFILE -/**************************************************************************** - * get the current readaddress - ****************************************************************************/ -static unsigned rti860_get_readaddress( unsigned int minor ) -{ - return - ((unsigned)(inw(adchstmem_reg) & 0x0003) << 16) - + inw_p(hostmem_reg); -} - -/**************************************************************************** - * get the current writeaddress - ****************************************************************************/ -static unsigned rti860_get_writeaddress( unsigned int minor) -{ - unsigned short hiBits, hiTmp; - unsigned writeAdr; - /***** - Zu der folgenden Konstruktion siehe den Kommentar in Fuellstand. - *****/ - do { - hiBits = inw(adchstmem_reg) & 0x0300; - writeAdr = inw(adcmem_reg); - hiTmp = inw(adchstmem_reg) & 0x0300; - } while( hiBits!=hiTmp ); - writeAdr += ( (unsigned)hiBits << 8 ); - - return writeAdr; -} -#endif -/*****************************************************************/ -/* - get the current amount of data in the memory -*/ -static unsigned -rti860_get_filling( unsigned int minor ) -{ - unsigned writeAdr, readAdr; - unsigned short hiBits, hiTmp; - - /***** - Das Problem beim Auslesen der Schreibadresse ist, daß zwei - Speicherzellen aus der Karte gelesen werden müssen, und es ist - nicht ausgeschlossen, daß die Karte die Schreibadresse zwischen - den beiden Zugriffen erhöht. Wenn diese Erhöhung über die - 0xFFFF-Marke hinausgeht, passen die beiden gelesenen Werte nicht - zueinander, egal in welcher Reihenfolge man sie einliest. Deshalb - die folgende Konstruktion: - *****/ - do { - hiBits = inw(adchstmem_reg) & 0x0300; - writeAdr = inw(adcmem_reg); - hiTmp = inw(adchstmem_reg) & 0x0300; - } while( hiBits!=hiTmp ); - writeAdr += ( (unsigned)hiBits << 8 ); - - hiBits = inw(adchstmem_reg) & 0x0003; - readAdr = inw(hostmem_reg) + ( (unsigned)hiBits << 16 ); - - if( writeAdr>=readAdr ){ - return writeAdr - readAdr; - } else { - return writeAdr + RTI860_MEMSIZE - readAdr; - } -} - -/**************************************************************************** - * interrupt service routine - ****************************************************************************/ -static void rti860_interrupt( int irq, struct pt_regs *regs ) -{ - /*printk("irq%d\n",irq);*/ - /* wake us up */ - - wake_up(&rti860_wait_q); -} - -/**************************************************************************** - * timer service routine - ****************************************************************************/ -static void rti860_timer( unsigned long data ) -{ - /*printk("timer%ld\n",data);*/ - /* wake us up */ - wake_up(&rti860_wait_q); -} - -/**************************************************************************** - * allocate the interrupt - ****************************************************************************/ -static void rti860_alloc_irq( int minor ) -{ - int ret; - - /* irq already allocated from driver ? */ - if( irq_count[rti860[INDEX(minor)].irq] == 0 ) { - - /* get the interrupt */ - ret = request_irq(rti860[INDEX(minor)].irq, - rti860_interrupt, - 0/*SA_INTERRUPT*/, - "rti860", - NULL); - if( ret ) { - /* no interrupt */ - printk(KERN_WARNING - "cannot allocate irq%d forrti860 device, " - "switching to polling mode.\n", - rti860[INDEX(minor)].irq); - rti860[INDEX(minor)].flags &= ~RTI860_F_IRQ; - return; - } - else { - /* got interrupt */ - printk(KERN_INFO "allocated irq%d for rti860 device\n", - rti860[INDEX(minor)].irq); - } - } - - /* increase irq count */ - irq_count[rti860[INDEX(minor)].irq]++; - - /* set flags */ - rti860[INDEX(minor)].flags |= RTI860_F_IRQ; - -} - -/**************************************************************************** - * free the interrupt - ****************************************************************************/ -static void rti860_free_irq(int minor) -{ - /* interrupt to free ? */ - if( rti860[INDEX(minor)].flags & RTI860_F_IRQ ) { - - /* decrease irq_count */ - if( irq_count[rti860[INDEX(minor)].irq] == 0 ) { - printk("rti860: irq_count less than zero! setting back...\n"); - irq_count[rti860[INDEX(minor)].irq] = 0; - } - - if( --irq_count[rti860[INDEX(minor)].irq] == 0 ) { - /* free interrupt and reset flags */ - free_irq( rti860[INDEX(minor)].irq, NULL ); - printk(KERN_INFO "freed irq%d of rti860 device\n", - rti860[INDEX(minor)].irq); - } - - /* reset flags */ - rti860[INDEX(minor)].flags &= ~RTI860_F_IRQ; - - } -} - -/**************************************************************************** - * read data from hardware - ****************************************************************************/ -static int rti860_read(struct inode *inode, struct file *file, char *buf, - int count) -{ - int ret, pre, post; - int index=0; - unsigned num_samples = 0; - unsigned int minor = MINOR(inode->i_rdev); -#if 0 - static unsigned long jiffies1,jiffies2; - unsigned dummy; -#endif -#if 0 - unsigned c[5],w,i; - static unsigned long mittel,stdabw,min,max,n; - static unsigned a[100]; -#endif - -#if 0 - jiffies1=jiffies; -#endif - - /***** only even byte count allowed */ - count &= 0xFFFFFFFE; - - /* check user memory */ - ret = verify_area( VERIFY_WRITE, buf, count ); - if( ret ) return ret; - - /***** start the driver and the device, if not yet busy. */ - if( (rti860[INDEX(minor)].flags & RTI860_F_BUSY) == 0 ) { - - if( rti860[INDEX(minor)].irq > 0 ) { - /* we want an interupt, so get it */ - rti860_alloc_irq(minor); - } - /* reset and start the hardware */ - rti860_start(minor); - - rti860[INDEX(minor)].flags |= RTI860_F_BUSY; - } - - num_samples = rti860_get_filling(minor); - - /***** read all the data */ - while( index < count ) { - - /***** Check for overflow and restart device in restart-mode */ - if( inw(status_reg) & (1<<6) ) { - if( rti860[INDEX(minor)].flags & RTI860_F_RESTART ) { - rti860_start(minor); - } else { - /* return data already read or error if nothing read */ - return index ? index : -EIO; - } - } - - /***** - We are about to enter a wait-loop below which includes some - sleeping. In polling mode, or if hardware fifo overflow happens at - the wrong time, there will be no more samples arriving anymore for - a long time. If this time is longer than the timeout, the process - will get an ETIME error, however only, if an ioctl() specified a - certain timeout. - *****/ - if( rti860[INDEX(minor)].timeout ) { - current->timeout = - jiffies + SEC2JIFFY(rti860[INDEX(minor)].timeout); - } - - /***** This is the wait-loop */ - while( !(num_samples=rti860_get_filling(minor)) ) { - - /* non blocked ? */ - if( file->f_flags & O_NONBLOCK ) return index; - - /***** fire a timer, if in polling mode */ - if((rti860[INDEX(minor)].flags & RTI860_F_IRQ) == 0 ){ - - /* check if timer already set */ - if( timer[INDEX(minor)].next == NULL - && timer[INDEX(minor)].prev == NULL ) { - - timer[INDEX(minor)].expires = - jiffies + rti860[INDEX(minor)].sleep_time; - add_timer( &(timer[INDEX(minor)]) ); - } - } - - /***** fall asleep until interrupt or timer arrives */ - interruptible_sleep_on(&rti860_wait_q); - - if (current->signal & ~current->blocked) { - return index; - } - - /***** timeout occured ? */ - if( current->timeout==0 ) return (-ETIME); - } - - if( num_samples > (count-index)/sizeof(short) ) - num_samples = (count-index)/sizeof(short); - - pre = inw(adchstmem_reg)&0x2; - - for( ; num_samples>0; num_samples--) { - /* read data and copy to user space */ - /* division by 16 because the 4 lower bits are not used */ - put_fs_word( (short)inw_p(datamem_reg)/16, &(buf[index])); - index = index + sizeof(short); - - post = inw(adchstmem_reg)&0x2; - if( pre != post ) { - outw( 0x8000, flgsclr_reg ); - } - } - } - -#if 0 - printk("%ld %ld %d\n", - jiffies-jiffies1, - jiffies-jiffies2, - dummy); - jiffies2=jiffies; -#endif - - return index; -} - -/**************************************************************************** - * test if data can be read - ****************************************************************************/ -static int rti860_select(struct inode *inode, struct file *file, - int sel_type, select_table *wait) -{ - unsigned int minor = MINOR(inode->i_rdev); - - /* ready for read ? */ - if( sel_type == SEL_IN ) { - - /* data available ? */ - if( rti860_get_filling(minor) == 0 ) { - - /* insert in wait queue */ - select_wait(&rti860_wait_q,wait); - - /* nothing to read */ - return 0; - } - - /* ready to read */ - return 1; - } - - /* always ready for write and exceptions */ - return 1; -} -/*****************************************************************/ -static char -checkParams(Rti860 *p) -{ - /***** - There is an enumeration type with limited range for channel. - *****/ - if( p->channel<-16 || p->channel>6 ) return 0; - - /***** - There is an enumeration type with limited range for trigger type. - *****/ - if( p->trigger>5 ) return 0; - - /***** - Ticks must be positive or 16bit negative but not 0,-1,-2; - *****/ - if( p->tics<=-65536 ) return 0; - if( p->tics<=0 && p->tics>=-1 ) return 0; - - /***** - We allow all irqs which can be jumpered according table 2.4 (page - 2-8) of the rti860 manual. - *****/ - if( p->irq!=0 && p->irq!=3 && p->irq!=5 && p->irq!=7 - && p->irq!=10 && p->irq!=11 && p->irq!=12 && p->irq != 15) - return 0; - - if( p->sleep_time<1 ) return 0; - return 1; -} -/*****************************************************************/ -static int -rti860_ioctl(struct inode *inode, struct file *file, - unsigned int cmd, unsigned long arg) -{ - unsigned int minor = MINOR(inode->i_rdev); - Rti860 tmprti860; - Rti860 *ptr = (Rti860 *)arg; - int error; - - switch( cmd ) { - case RTI860_SET_PAR: - /* device busy ? */ - if( rti860[INDEX(minor)].flags & RTI860_F_BUSY ) return (-EBUSY); - - /* check memory */ - error = verify_area( VERIFY_READ, ptr, sizeof(Rti860) ); - if (error) return (error); - - /* copy data */ - memcpy_fromfs( (void *)&tmprti860, ptr, sizeof(Rti860) ); - - /***** - We probably must correct the tics. However we do this only for - the internal clock. Doing it for the external clock is rather - useless, because the divider tends to so small then that division - by 2 or 4 will invalidate it. - We do this before checking parameters because the parameters must - come out correct afterwards. - *****/ - if( tmprti860.channel >= 0 && tmprti860.tics>0) { - switch( tmprti860.channel ) { - case Channel1_16: - tmprti860.tics /= 4; - break; - case Channel1_8: - case Channel9_16: - tmprti860.tics /= 2; - break; - case Channel1_4: - case Channel5_8: - case Channel9_12: - case Channel13_16: - break; - default: - return (-EINVAL); - } - } - - /* check validity of parameters */ - if( !checkParams(&tmprti860) ) return -EINVAL; - - /* set data */ - rti860[INDEX(minor)].flags = - (rti860[INDEX(minor)].flags & ~RTI860_F_USER) | - (tmprti860.flags & RTI860_F_USER); - rti860[INDEX(minor)].channel = tmprti860.channel; - rti860[INDEX(minor)].trigger = tmprti860.trigger; - rti860[INDEX(minor)].level = tmprti860.level; - rti860[INDEX(minor)].tics = tmprti860.tics; - rti860[INDEX(minor)].irq = tmprti860.irq; - rti860[INDEX(minor)].timeout = tmprti860.timeout; - rti860[INDEX(minor)].sleep_time = tmprti860.sleep_time; - return 0; - - - - case RTI860_GET_PAR: /* get actual parameters */ - /* check memory */ - - error = verify_area(VERIFY_WRITE, ptr, sizeof(Rti860)); - if( error ) return error; - - tmprti860 = rti860[INDEX(minor)]; - - /***** need to correct the outgoing ticks? */ - if( tmprti860.channel >= 0 && tmprti860.tics>0) { - switch( tmprti860.channel ) { - case Channel1_16: - tmprti860.tics *= 4; - break; - case Channel1_8: - case Channel9_16: - tmprti860.tics *= 2; - break; - default: - break; - } - } - /* copy data */ - memcpy_tofs(ptr, (void *)(&tmprti860), sizeof(Rti860)); - - return 0; - - case RTI860_START: - /* device busy ? */ - if( (rti860[INDEX(minor)].flags & RTI860_F_BUSY) == 0 ) { - if( rti860[INDEX(minor)].irq > 0 ) { - /* we need an interrupt, get it */ - rti860_alloc_irq(minor); - } - /* set device busy */ - rti860[INDEX(minor)].flags |= RTI860_F_BUSY; - } - - /* reset and start the hardware */ - rti860_start(minor); - - /* oK */ - return 0; - - case RTI860_RESET: - /* hardware reset */ - rti860_init(minor); - - /* set device not busy */ - rti860[INDEX(minor)].flags &= ~RTI860_F_BUSY; - - /* oK */ - return 0; - - default: - return (-EINVAL); - } -} - -/**************************************************************************** - * open the device - ****************************************************************************/ -static int rti860_open(struct inode *inode, struct file *file) -{ - unsigned int minor = MINOR(inode->i_rdev); - - /* check minor device number */ - if( minor >= RTI860_NO ) - return (-ENODEV); - - /* check if hardware present */ - if( !(rti860[INDEX(minor)].flags & RTI860_F_PRESENT) ) - return (-ENODEV); - - /* open for write ? */ - if( (file->f_flags & O_ACCMODE) != O_RDONLY ) - return (-EROFS); - - /* already opened ? */ - if( rti860[INDEX(minor)].flags & RTI860_F_OPEN ) - return (-EBUSY); - - /* set device open */ - rti860[INDEX(minor)].flags |= RTI860_F_OPEN; - - /* oK */ - return 0; -} - -/**************************************************************************** - * close the device - ****************************************************************************/ -static void rti860_release(struct inode *inode, struct file *file) -{ - unsigned int minor = MINOR(inode->i_rdev); - - /* hardware reset */ - rti860_init(minor); - - /* clear irq */ - rti860_free_irq(minor); - - /* set device not busy */ - rti860[INDEX(minor)].flags &= ~RTI860_F_BUSY; - - /* set device closed */ - rti860[INDEX(minor)].flags &= ~RTI860_F_OPEN; -} - -static struct file_operations rti860_fops = { - NULL, /* rti860_lseek */ - rti860_read, - NULL, /* rti860_write */ - NULL, /* rti860_readdir */ - rti860_select, - rti860_ioctl, - NULL, /* rti860_mmap */ - rti860_open, - rti860_release -}; - -/**************************************************************************** - * initialize the device - ****************************************************************************/ -int init_module( void ) -{ - unsigned long address; - unsigned int minor, num=1; - - if( register_chrdev(RTI860_MAJOR, "rti860", &rti860_fops) ) - { - printk(KERN_ERR - "unable to get major %d for rti860 device\n", - RTI860_MAJOR); - return -EIO; - } - - /* find the rti860 */ - for( minor=0,address=0x100 ; address<=0x3E0 ; address+=0x20,minor++ ) { - - /* check if rti860 is present at address */ - if( (inw(address) & 0xF000) == 0x2000 ) { - - printk(KERN_INFO "rti860 found at 0x%lX\n", address ); - - INDEX(minor) = num++; - - /* - * Set present flag and base address - */ - rti860[INDEX(minor)].flags |= RTI860_F_PRESENT; - rti860[INDEX(minor)].base = address; - - /* maximal number of rti860's reached */ - if( num >= RTI860_MAX ) break; - } - } - - /* calculate delay loops */ - loops_per_msec = loops_per_sec/1000; - - printk(KERN_INFO "rti860 device driver installed.\n"); - - return 0; - -} - -/**************************************************************************** - * kill the device - ****************************************************************************/ -void cleanup_module(void) -{ - int i; - - unregister_chrdev(RTI860_MAJOR, "rti860"); - for(i=0; i