-Driver: ni-atmio.o
-Description: National Instruments AT-MIO-E series (all boards)
+Driver: adl_pci9118.o
+Description: Adlink PCI-9118DG, PCI-9118HG, PCI-9118HR
+Author: Michal Dobes <majkl@tesnet.cz>
+Status works
+
+This driver supports AI, AO, DI and DO subdevices.
+AI subdevice support cmd, insn and mode0-4 interface,
+other subdevices support insn and mode0 interface.
+For AI:
+- If cmd->scan_begin_src=TRIG_EXT (or trigger mode4) then trigger input
+ is TGIN (pin 46).
+- If cmd->convert_src=TRIG_EXT (or trigger mode3) then trigger input
+ is EXTTRG (pin 44).
+
+
+
+Driver: comedi_parport.o
+Description: Standard PC parallel port
Author: ds
-Status: mainly limited by Comedi infrastructure
+Status: works in immediate mode
-The isapnptools package is required to use this board. Use isapnp to
-configure the I/O base for the board, and then pass the same value as
-a parameter in comedi_config. A sample isapnp.conf file is included
-in the etc/ directory.
+A cheap and easy way to get a few more digital I/O lines. Steal
+additional parallel ports from old computers or your neighbors'
+computers.
-Assuming that the NI spec is correct, the driver should correctly
-identify every board in the series. Each channel should have the
-appropriate parameters, i.e., input/output ranges, number of bits,
-etc. If the driver fails to recognize your card or does not have
-the correct parameters, please contact me.
-Comedilib includes a utility to autocalibrate these boards. The
-boards seem to boot into a state where the all calibration DACs
-are at one extreme of their range, thus the default calibration
-is terrible. Calibration at boot is strongly encouraged.
+Parallel Output Port Lines:
+
+pin subdev chan aka
+--- ------ ---- ---
+1 2 0 strobe
+2 0 0 data 0
+3 0 1 data 1
+4 0 2 data 2
+5 0 3 data 3
+6 0 4 data 4
+7 0 5 data 5
+8 0 6 data 6
+9 0 7 data 7
+10 1 3 acknowledge
+11 1 4 busy
+12 1 2 output
+13 1 1 printer selected
+14 2 1 auto LF
+15 1 0 error
+16 2 2 init
+17 2 3 select printer
+18-25 ground
+
+
+Notes:
+
+Channel 0 and 2 are output, channel 1 is input. I know that it
+is possible to change this with ECP/EPP parallel ports, but this
+driver is a cheap hack.
+
+Pins 13 and 14 are inverted once by comedi and once by the
+hardware, thus cancelling the effect.
+
+Pin 1 is a strobe, thus acts like one. There's no way in software
+to change this, at least on a standard parallel port.
+
+Please report any sucesses/failures.
+
+Driver: das08-new.o
+Description: DAS-08 compatible boards
+Authors: Warren Jasper, ds
+Status: in development
+
+This is a rewrite of the das08 and das08jr drivers.
+
Driver: das08.o
Description: ComputerBoards, Keithley Metrabyte DAS-08
+Driver: das16-new.o
+Description: DAS16 compatible boards
+Authors: Sam Moore, Warren Jasper, ds
+Status: in development
+
+A rewrite of the das16 and das1600 drivers.
+
+
Driver: das16.o
Description: CIO-DAS16 (& compatibles)
Authors: Sam Moore, Warren Jasper, ds
+Driver: das800.o
+Description: Keithley Metrabyte DAS800 (& compatibles)
+Author: Frank Mori Hess <fmhess@uiuc.edu>
+Status: in development
-
-
Driver: dt2811.o
Description: Data Translation DT2811
Author: ds
-
-Driver: ni_pcidio.o
-Description: National Instruments PCI-DIO32HS, PCI-DIO96, PCI-6533, PCI-6503
+Driver: ni_atmio.o
+Description: National Instruments AT-MIO-E series (all boards)
Author: ds
-Status: works in immediate mode
-
-The DIO-96 appears as four 8255 subdevices. See the 8255
-driver notes for details.
+Status: mainly limited by Comedi infrastructure
-The DIO32HS board appears as one subdevice, with 32 channels.
-Each channel is individually I/O configurable. The channel order,
-as one might guess, is 0=A0, 1=A1, 2=A2, ... 8=B0, 16=C0, 24=D0.
+The isapnptools package is required to use this board. Use isapnp to
+configure the I/O base for the board, and then pass the same value as
+a parameter in comedi_config. A sample isapnp.conf file is included
+in the etc/ directory.
-DMA is halfway completed, but not operational, for the PCI-DIO32HS.
-This driver could be easily modified to support AT-MIO32HS and
-AT-MIO96.
+Assuming that the NI spec is correct, the driver should correctly
+identify every board in the series. Each channel should have the
+appropriate parameters, i.e., input/output ranges, number of bits,
+etc. If the driver fails to recognize your card or does not have
+the correct parameters, please contact me.
+Comedilib includes a utility to autocalibrate these boards. The
+boards seem to boot into a state where the all calibration DACs
+are at one extreme of their range, thus the default calibration
+is terrible. Calibration at boot is strongly encouraged.
-Driver: comedi_parport.o
-Description: Standard PC parallel port
-Author: ds
-Status: works in immediate mode
+Driver: ni_atmio16d.o
+Description: National Instruments AT-MIO-16D
+Author: Chris R. Baugher <baugher@enteract.com>
+Status: unknown
-A cheap and easy way to get a few more digital I/O lines. Steal
-additional parallel ports from old computers or your neighbors'
-computers.
-Parallel Output Port Lines:
+Driver: ni_mio_cs.o
+Description: National Instruments DAQCard E series
+Author: ds
+Status: works
-pin subdev chan aka
---- ------ ---- ---
-1 2 0 strobe
-2 0 0 data 0
-3 0 1 data 1
-4 0 2 data 2
-5 0 3 data 3
-6 0 4 data 4
-7 0 5 data 5
-8 0 6 data 6
-9 0 7 data 7
-10 1 3 acknowledge
-11 1 4 busy
-12 1 2 output
-13 1 1 printer selected
-14 2 1 auto LF
-15 1 0 error
-16 2 2 init
-17 2 3 select printer
-18-25 ground
-Notes:
+Driver: ni_pcidio.o
+Description: National Instruments PCI-DIO32HS, PCI-DIO96, PCI-6533, PCI-6503
+Author: ds
+Status: works in immediate mode
-Channel 0 and 2 are output, channel 1 is input. I know that it
-is possible to change this with ECP/EPP parallel ports, but this
-driver is a cheap hack.
+The DIO-96 appears as four 8255 subdevices. See the 8255
+driver notes for details.
-Pins 13 and 14 are inverted once by comedi and once by the
-hardware, thus cancelling the effect.
+The DIO32HS board appears as one subdevice, with 32 channels.
+Each channel is individually I/O configurable. The channel order,
+as one might guess, is 0=A0, 1=A1, 2=A2, ... 8=B0, 16=C0, 24=D0.
-Pin 1 is a strobe, thus acts like one. There's no way in software
-to change this, at least on a standard parallel port.
+DMA is halfway completed, but not operational, for the PCI-DIO32HS.
+This driver could be easily modified to support AT-MIO32HS and
+AT-MIO96.
-Please report any sucesses/failures.
See the head of the source file pcl818.c for configuration options.
+
+Driver: quatech_daqp_cs.o
+Description: Quatech DAQP PCMCIA data capture cards
+Author: Brent Baccala <baccala@freesoft.org>
+Status: unkown
+
+
+
Driver: rti800.o
Description: Analog Devices RTI-800/815
Author: ds
Status: works
-Driver: adl_pci9118.o
-Description: Adlink PCI-9118DG, PCI-9118HG, PCI-9118HR
-Author: Michal Dobes <majkl@tesnet.cz>
-Status works
-
-This driver supports AI, AO, DI and DO subdevices.
-AI subdevice support cmd, insn and mode0-4 interface,
-other subdevices support insn and mode0 interface.
-For AI:
-- If cmd->scan_begin_src=TRIG_EXT (or trigger mode4) then trigger input
- is TGIN (pin 46).
-- If cmd->convert_src=TRIG_EXT (or trigger mode3) then trigger input
- is EXTTRG (pin 44).
-
-
projects / comedi.git / commitdiff